Furnace Installation in Irving, TX — Residential Heating Specialists
New Furnace. Right Size. Done Right.
Serving Irving 7 Days a Week
Residential Only
Irving homeowners trust Mas Heating Airconditioning for furnace installation and replacement that lasts. We've been sizing, installing, and testing heating systems across Irving and the DFW area since 2014 — no guesswork, no shortcuts, no surprises on the invoice.
Furnace Installation in Irving, TX — What You Need to Know Before You Decide
Mas Heating Airconditioning provides residential furnace installation and replacement in Irving, TX and surrounding DFW communities. Whether your current system has reached the end of its lifespan or you're upgrading to a high-efficiency model, our team handles the full process — load calculation, equipment selection, installation, and final testing — so your home heats evenly and efficiently from day one. We serve Irving homeowners exclusively on the residential side, which means every installation is approached with the care and detail a family home deserves.
Is It Time to Replace Your Furnace?
Most furnaces last between 15 and 20 years. If yours is approaching that range — or showing any of the signs below — a new installation is likely the smarter investment compared to continued repairs.
Your Furnace Is Over 15 Years Old
An aging furnace works harder to produce the same heat, driving up your energy bills every month. Even if it hasn't failed yet, efficiency losses are already costing you.
Repair Costs Are Adding Up
When a single repair approaches 50% of the cost of a new unit, replacement becomes the financially sound decision. Our team can walk you through the numbers during your estimate so you can decide with confidence — not pressure.
Uneven Heating Across Rooms
Hot and cold spots throughout the house are a common sign that your furnace can no longer distribute heat consistently. A properly sized and installed new system solves this at the source.
Your Energy Bills Keep Climbing
Older furnaces operate at AFUE ratings of 60–70%, meaning up to 40% of the fuel you pay for escapes unused. Modern high-efficiency units reach 96–98% AFUE — a real difference on your monthly utility bill.
Unusual Noises or Frequent Cycling
Banging, rattling, or a furnace that turns on and off repeatedly are signs of mechanical stress. These symptoms often escalate quickly in aging systems.
Furnace Installation in Irving, TX — What You Need to Know Before You Decide
Mas Heating Airconditioning provides residential furnace installation and replacement in Irving, TX and surrounding DFW communities. Whether your current system has reached the end of its lifespan or you're upgrading to a high-efficiency model, our team handles the full process — load calculation, equipment selection, installation, and final testing — so your home heats evenly and efficiently from day one. We serve Irving homeowners exclusively on the residential side, which means every installation is approached with the care and detail a family home deserves.
Can't wait? Call us directly:
(214) 530-6579
Is It Time to Replace Your Furnace?
Most furnaces last between 15 and 20 years. If yours is approaching that range — or showing any of the signs below — a new installation is likely the smarter investment compared to continued repairs.
Your Furnace Is Over 15 Years Old
An aging furnace works harder to produce the same heat, driving up your energy bills every month. Even if it hasn't failed yet, efficiency losses are already costing you.
Repair Costs Are Adding Up
When a single repair approaches 50% of the cost of a new unit, replacement becomes the financially sound decision. Our team can walk you through the numbers during your estimate so you can decide with confidence — not pressure.
Uneven Heating Across Rooms
Hot and cold spots throughout the house are a common sign that your furnace can no longer distribute heat consistently. A properly sized and installed new system solves this at the source.
Your Energy Bills Keep Climbing
Older furnaces operate at AFUE ratings of 60–70%, meaning up to 40% of the fuel you pay for escapes unused. Modern high-efficiency units reach 96–98% AFUE — a real difference on your monthly utility bill.
Unusual Noises or Frequent Cycling
Banging, rattling, or a furnace that turns on and off repeatedly are signs of mechanical stress. These symptoms often escalate quickly in aging systems.
Gas vs. High-Efficiency Furnace — Which One Is Right for Your Irving Home?
Not every home needs the same furnace. Here's a straightforward comparison to help you understand your options before we talk.
Standard Gas Furnace (80% AFUE)
The most common choice for Irving homes with existing gas lines. Reliable, cost-effective upfront, and simpler to install in homes with traditional venting. A solid choice if you want dependable heat without the premium price of high-efficiency equipment.
High-Efficiency Gas Furnace (90–98% AFUE)
Extracts significantly more heat from the same amount of fuel. The installation cost is higher, but monthly savings on your gas bill close the gap over time — especially in homes with high heating usage or larger square footage. Requires PVC exhaust venting, which we handle during installation.
Electric Furnace
An option for homes without a gas line. Lower upfront cost, no combustion risks, but operating costs in Texas are typically higher than gas long-term. We'll advise honestly based on your home's setup.
During your free estimate, we perform a Manual J load calculation — the industry-standard method for sizing your furnace correctly to your home's square footage, insulation, and layout. An oversized or undersized unit is one of the most common and costly mistakes in furnace installation. We don't skip this step.
How Our Furnace Installation Process Works
We follow a structured process on every installation — no improvising, no corners cut.
*Free In-Home Estimate and Load Calculation
We visit your home, assess your current system and ductwork, and calculate the exact heating capacity your home requires. You get a clear, written estimate before we schedule anything.
*Equipment Selection
Based on the load calculation and your budget, we recommend the furnace that fits your home — not the one with the highest margin. We work with multiple equipment options across efficiency levels.
*Safe Removal of the Old Unit
We disconnect and remove your existing furnace following proper safety procedures, including gas line handling and proper disposal of the old equipment.
*Installation and Ductwork Check
Your new furnace is installed, connected to your existing ductwork, and tested for proper airflow distribution. If we find duct issues that would compromise performance, we tell you — with options, not ultimatums.
*System Testing and Thermostat Calibration
We run the system through a full operational test, verify heat output across your home, and calibrate your thermostat for accurate temperature control. We don't leave until everything is working correctly.
*Walkthrough and Maintenance Guidance
Before we go, we walk you through how to operate your new system, when to change filters, and what to watch for in the first season. A well-maintained furnace performs better and lasts longer
What Does Furnace Installation Cost in Irving, TX?
Furnace installation cost depends on four variables: equipment type, efficiency rating, your home's size, and the condition of your existing ductwork. Here are realistic ranges for Irving homeowners.
High-Efficiency Furnace Installation
A 90–98% AFUE system, including PVC venting and full installation, typically falls in the $4,000 to $7,500 range. The higher upfront cost is partially offset by lower monthly gas bills.
Standard Gas Furnace Installation
Equipment and installation for a standard 80% AFUE gas furnace typically ranges from $2,500 to $4,500 depending on unit capacity and any ductwork adjustments needed.
Furnace and AC Replacement Together
Replacing both systems at the same time is often more cost-effective than doing them separately — one mobilization, one ductwork check, one installation window. Combined system replacement in Irving typically runs $6,000 to $12,000 depending on equipment and home size.
These are honest ranges based on what residential installations in the DFW area typically involve. Your exact quote depends on your home. That's why we start with a free in-home estimate — so you get a real number, not a guess.
Why Irving Homeowners Choose Mas Heating for Furnace Installation
Proper Sizing on Every Job
We perform a Manual J load calculation on every installation. No eyeballing square footage, no reusing the old unit's specs. A correctly sized furnace is the foundation of efficient, comfortable heat.
12+ Years of Residential HVAC Experience in Irving
Since 2014, we've worked exclusively with homeowners in Irving and the surrounding DFW area. Furnace installation is not a side service for us — it's part of what we do every heating season.
Available 7 Days a Week, 8 AM to 8 PM
Heating systems don't fail on a schedule. We're available Monday through Sunday so you can book your installation or estimate without rearranging your week.
Transparent Pricing Before We Start
You receive a written estimate before any work begins. The number on the estimate is the number on the invoice. We explain every line item so you understand what you're paying for.
Bilingual Service — English and Spanish
Our team serves Irving's bilingual community in both English and Spanish — whichever is more comfortable for you.
Furnace Installation Service Areas Near Irving, TX
Mas Heating Airconditioning provides furnace installation throughout Irving, TX and nearby communities including Coppell, Arlington, Grand Prairie, and Dallas. If you're within the DFW area and need a residential furnace installed or replaced, we're the team to call. Our address is 3026 Steven St, Irving, TX 75062 — locally based and serving neighbors, not just customers.
Frequently Asked Questions About Furnace Installation in Irving, TX
How long does a furnace installation take?
Most residential furnace installations are completed in 4 to 8 hours, depending on the complexity of the job and whether ductwork modifications are needed. We schedule a window and stick to it.
Do I need a permit for furnace installation in Irving, TX?
In most cases, yes — furnace installations in Irving require a mechanical permit through the City of Irving. We handle the permitting process as part of the installation so you don't have to navigate city paperwork.
How do I know what size furnace my home needs?
Furnace size is measured in BTUs and should be calculated based on your home's square footage, ceiling height, insulation levels, and local climate — not simply the size of the unit you're replacing. We perform a Manual J load calculation on every job to get this right.
Is it worth replacing my furnace if it still works?
If your furnace is over 15 years old and your repair costs are escalating, replacement is usually the smarter long-term investment. A new high-efficiency furnace can reduce your heating costs significantly and comes with a manufacturer warranty your old system no longer has.
Can you add air conditioning to an existing furnace installation?
Yes. If you're replacing your furnace, it's an ideal time to evaluate your AC system as well. We can install a complete matched system — furnace and air handler or condenser — in the same visit, which reduces labor and ensures both components are properly sized for each other.
What brands of furnace do you install?
We work with multiple residential furnace brands and select equipment based on your home's requirements and your budget — not brand commissions. During your estimate, we'll recommend the specific unit that fits your situation.
How often should a new furnace be serviced after installation?
A new furnace should be serviced once a year — ideally before the heating season begins. Annual maintenance keeps your system operating at peak efficiency, extends its lifespan, and protects the manufacturer warranty. Learn more about our heating tune-up in Irving TX.
What payment options do you accept?
We accept major credit cards, debit, and check. Contact us directly at 214-530-6579 to discuss payment arrangements for your installation.
Ready to Install Your New Furnace in Irving? Let's Talk.
A new furnace is one of the most important investments you'll make in your home's comfort and efficiency. Mas Heating Airconditioning makes the process straightforward — honest sizing, transparent pricing, and an installation done right the first time.
Call us at 214-530-6579 — available 7 days a week, 8 AM to 8 PM.
Or use our contact form to schedule your free in-home estimate
We serve Irving, Coppell, Arlington, Grand Prairie, and Dallas. 3026 Steven St, Irving, TX 75062
(214) 530-6579
After-hours emergency service available with additional fee — disclosed before work begins.